• RSS
  • Facebook
  • Twitter
  • Linkedin
Home > Error Failed > Error Failed To Send A Fma Eventrc=-1

Error Failed To Send A Fma Eventrc=-1

But here is where is gets interesting. Workaround: Use the ILOM web GUI interface to configure alerts, rather than ILOM CLI, to avoid issues when modifying and displaying alerts. Sufficient spares existed and one was automatically attached to the damaged pool. Likewise, the server BIOS also provides a GUID. this contact form

Workaround: If you experience this issue, temporarily unplug one of the server’s internal hard disks to boot from a CD or external device. pool1 will be a 1GB mirrored pool using disk1 and disk2. This card does not support network boot in X4140, X4240 or X4440 servers. And two hits to zfs-retire.

If any issue with fmd daemon itself, you can see the service going into maintenance and check the SMF log or svcs -x output will help you find out if fmd Action : Run 'zpool status -x' and replace the bad device. # zpool status -x pool: pool1 state: DEGRADED status: One or more devices could not be opened. MAC Failure During Late Packet Collision Might Hang System (6648502) On rare occasions, a collision occurring during the preparation of the last byte of a transmit packet’s FCS might cause a When talking about Solaris I will use the phrase "The Vastness of Solaris".

  1. Thanks Mark Posted by Mark Huff on February 20, 2008 at 08:47 AM CST # Great example of taking a real world problem and showing how Solaris behaves.
  2. Bob is also a contributing author of Solaris 10 Virtualization Essentials.
  3. Refer to the Sun Integrated Lights Out Manager User’s Guide, for information on how to reset the service processor).

In certain rare circumstances, when using the ILOM Web interface or CLI interface to configure the serial port, the settings might not properly save and the ILOM service processor becomes unresponsive. Oh, and clear the FMA stats while we're at it. # zpool clear # zpool detach pool2 spare1 # fmadm reset zfs-diagnosis fmadm: zfs-diagnosis module has been reset # fmadm reset But my advise it to apply latest kernel patches to get the impacted memory identified. see: scrub: resilver completed with 602 errors on Mon Feb 18 13:20:14 2008 config: NAME STATE READ WRITE CKSUM pool2 DEGRADED 0 0 2.60K mirror DEGRADED 0 0 2.60K spare

Configure the Nvidia NIC and any connected port to either the same duplex mode or both ports configured for auto-negotiate. If an error is reported by Solaris FMA (Fault Management Architecture) for one of the functions behind that bridge chip, it might report the wrong slot number. This does not indicate a problem and can be ignored. The off-line condition is not silent.

But the key point in Isaac's multiplicity discussion is how the cornucopia of Solaris features work together to do some pretty spectacular (and competitively differentiating) things. ZFS and FMA are two great tastes that taste great together. I assume these are zfs checksum errors, automagically fixed by the zfs gods? If you have attended a Solaris Boot Camp or Tech Day in the last few years you get an idea of what we are talking about - when we go on

New with T5140/T5240 is the hardware's capability to ensure a single lane failover without system interruption. browse this site Hence you are getting the error message from SC - SC Alert: [ID 599537 daemon.error] Chassis | major:ERROR: Failed to send a fma event(rc=-1) ereport.cpu.ultraSPARC-T2.dac Simple solution for this problem could Refer to for more information. remote errors: With multiple processors in the system, it is possible that one T2 Plus can trigger an error in another T2 Plus (e.g.

Error details: Exception 'Database not found or not accessible' of type 'Citrix.Fma.Sdk.Dal.DALDatabaseNotFoundException'. weblink For those not familiar with the kit, it provides a harness for executing fault management demos on CPU, Memory and PCI errors. I thought the module would take care of it. The TP-SCTS value in those messages (all from the same Service Center) is "F8", which represents a negative value and a hexadecimal value "F" which seems dubious, because it's not a

Hi, The problem was that cpumem-diagnosis module wasn't loaded. Workaround: Use ILOM as an alternate online means to check on drive status during a failure. action: Determine if the device needs to be replaced, and clear the errors using 'zpool clear' or replace the device with 'zpool replace'. navigate here PDUspy decodes that timestamp to 2007-09-02 11:51:47 GMT-3,75 which you get by multiplying 15 (F) x 0,25 = 3,75 - but I don't think thats according to a standard, despite the

Workaround: Until a long term fix is available, adding a second AC supply into systems that frequently exhibit this issue should significantly reduce the noise and associated false events. Response : The device has been marked as degraded. A “Hypertransport Link Protocol Error” indicates there is an MMIO mapping overlap or discrepancy in low 4 GB between PCI space and pure memory.

Workaround: To clear this fault, remove all AC cords for a short time, to reset both the SP and the server motherboard.

AMD Erratum 326: Misaligned Load Operation Might Cause Processor Core Hang (6682358) Under a rare and highly specific set of internal timing conditions, load operations with a misaligned operand might hang Example (dmidecode) ... The system returned: (22) Invalid argument The remote host or network may be down. pool2 will be a 512MB mirrored pool using disk3 and disk4.

Also sometime we see that the desktop's gives an unknown power state. Additional information on FB-DIMM diagnosis is in one of my earlier blogs. These events are caused by noise generated from early production power supplies (part number 300-2015-05). his comment is here A device (disk2) has failed and is no longer in operation.

see: scrub: resilver in progress, 4.94% done, 0h0m to go config: NAME STATE READ WRITE CKSUM pool1 DEGRADED 0 0 0 mirror DEGRADED 0 0 0 disk1 ONLINE 0 0 Now, let's do the unthinkable - let's corrupt both halves of the mirror. Jump to content Citrix Citrix Discussions Log In Knowledge Center Product Documentation Communities Blogs All CategoriesAppDNAArchived Products (includes End of Life)Citrix CloudCitrix Connector for System CenterCitrix Developer ExchangeCitrix Developer Network Refer to for more information.