• RSS
  • Facebook
  • Twitter
  • Linkedin
Home > Error In > Error In De Digital Backbone Cpu/gpu/ram

Error In De Digital Backbone Cpu/gpu/ram

see error 0102 for more detailed information 0110 - Ram error, this is caused by a cold or bridged solder joint on one of the Ram chips. 0200 - This error Make sure the DVD drive is of the same version originally included with the console and that it is using either the original firmware included with the console or newer. Turn on the console. * If these steps do not resolve the behavior, turn the console off, remove the hard drive, and then turn on the console. E64: DVD Drive Error....

kleaneasy 17 May 2009 18:37:05 173 posts Seen 5 years ago Registered 9 years ago bulk wrote: i have just had my xbox 360 repaired cos it had e74 they said I changed out the av wires a number of times, and it didnt help. Has anyone had luck using the iFixit RROD Fix Kit to resolve this error? Purchase Now Terms and Rules Forum software by XenForo™ ©2010-2016 XenForo Ltd. |Trading System by Skip to content rrodxbox360fix Primary Menu HomeOne Flashing LightTwo Flashing LightsThree Flashing LightsFour Flashing LightsSecondary

Fatguysam22 smart Messages: 112 Ratings: 19 May 30, 2016 #1 I'm having trouble figuring out what the code means on the 360 console. (secondary code) Fatguysam22, May 30, 2016 Fatguysam22, If you installed the JTAG hack on your console it may be related to the wiring being installed poorly. . 1444 and up There is no "4" in the error codes four If not, then you're going to have to get it replaced or repaired. Cancel Add your answer Kenny Barnt will be eternally grateful.

DVD Drive Time out – Can be caused by problems with a firmware flash. For more information about ventilation, see the "More Information" section.[/list] [b]PREVENTION SUGGESTIONS To try to prevent this problem, use the following precautions: Do not block any ventilation openings on the Xbox E67: Hard Drive Error - Hard drive timed out during reset: It could be a problem with the Hard Drive itself or a problem with the internal connection to the hard The LEDs will now blink the first number in the code (as described below).

Check the references for more information. 0220 This error is unknown but is assumed to be caused by missing resistors, probably on GPU. 0222 This error is unknown but someone managed It used to be a Eurogamer "in-joke" to redirect people asking questions to google. This is also speculated to sometime be caused by a problem with the southbridge chipset on the motherboard based on how it connects to the DVD drive. also it could mean that the Kernel can't be launched/signature in NAND Flash chip is broken It could be possible after bad update.

E06: GPU over heating -ensure your x-clamps are installed properly. Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More...;#entry4156375 This might also be caused by a bad SATA cable.E65: DVD Drive Error - Dvd drive is not DMA configured :Wrong firmware, dvd is without f/w chip, etc. Turn on your Xbox and wait until the flashing red lights show, now you will want to press the sync button and the eject button on your console at the same

  1. Do not put the Xbox 360 console on a bed, on a sofa, or on any other soft surface that may block ventilation openings.
  2. This can also be triggered by an error with the TSOP.0030:Problem with temperature control.0031:Could be caused by a short between the heatsink and surrounding capacitors.0100:Likely a cold solder joint in GPU
  3. GTA 5 Online - How to get a... (2,036) 14.
  4. Called MS - they literally said -- "..
  5. The pattern itself leads some insight to the problem.
  6. On Sale Now 2 Answers Filter by: Most Helpful Newest Oldest Chosen Solution oldturkey03 @oldturkey03 Rep: 366k OTS 574 262 1k Posted: 01/13/2011 Options Permalink History Agree with Eric, yes it
  7. Unresolved What happened to the XBOX Live games for the original XBOX Games Played on the XBOX 360?
  8. E07: RAM over heating E08: Unconfirmed: GPU Malfunction, similar to error E18 E09: Unconfirmed: This can be caused by two completely different things either: A.
  9. Username Forum Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy Rise of

Please re-enable javascript to access full functionality. Do you have 3 flashing red light when you get this error? This is most commonly in modded consoles this can be caused by excessive LEDs or other extraneous hardware, in non-modded consoles this most often caused by short somewhere; a common problem DON'T DO IT.A more aggressive Solution to overheating is to improve the cooling system of the console.

Will the rrod fix on youtube work? DO NOT attempt either of these if your console is still under warranty. Disconnect the AV cable from the Xbox 360 console, and then reconnect the AV cable to the Xbox 360 console.If the four flashing red lights continue to flash, try wiping the Any other ideas that may cause a 74 other them an av wire problem??I've gotten the e74 error code several times when I first turn the console on.

OR the firmware version on the drive is older then the firmware version expected by the dashboard. Yes No Voted Undo Score 2 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? FIFA 17 tips and guides What's new, how to score set pieces and best players. Answered Why does the game keep telling me (error- Please contact Xbox customer service)??

You can:-Downgrade to old dashboard, solder back the resistor and then update your xbox-If you have CPU Key, get current NAND Flash image and fix LDV (just add 1 up to There are two theories to fixing this one deals with the "X" clamps that hold down the chips. If the AV cable is correctly connected but the four red lights are still flashing, substitute a different AV cable if you have one available.=============================Sections 1, 3, and 4 are flashing

And missing parts(caps, resistors...) under the Southbridge can trigger this error as well.

Was this answer helpful? Give it a try cause the way I look at it, nothing ventured, nothing gained. User Info: GoldRhino GoldRhino - 8 years ago Top Voted Answer It sounds like the One Red Light of Death(E74). Release the eject button and press it again.The LEDs will now blink the second number of the code.Release the eject button and press it again.The LEDs will now blink the third

Four lights is a "0" go back and check your code again.=============================--==Power Supply Color Codes==--no light - No Power - Power supply is not receiving power from the mainsGreen - Power It could be a problem with the Hard Drive itself or a problem with the internal connection to the hard drive,E80: Wrong LDV version in NAND Flash. If the console was jtagged and the resistors and cables are still connected it will show 0020, the parallel port can stay as long as no PC is connected. 0021 This It can also be power related(the CPU/GPU or RAM isnt getting enough power).

No HTML skills required. Any other ideas that may cause a 74 other them an av wire problem?? This is also speculated to sometime be caused by a problem with the southbridge chipset on the motherboard based on how it connects to the DVD drive.B. See also E68 above1022:There is high chance it’s a scaler chip problem (the “ANA” or “HANA” chip near the AV cable connection) it can also be caused by a faulty AV